#ZYXEL VPN CLIENT MAC OS X MAC OS X#
#ZYXEL VPN CLIENT MAC OS X PASSWORD#

#ZYXEL VPN CLIENT MAC OS X MAC OS X#

Select Send all traffic over VPN connection to allow the L2TP/IPSec VPN traffic between ZyWALL/USG and MAC OS X system.ĥ Go back to Configuration and click Connect.ġ Go to ZyWALL/USG CONFIGURATION > VPN > IPSec VPN > VPN Connection, the Status connect icon is lit when the interface is connected.ĬONFIGURATION > VPN > IPSec VPN > VPN ConnectionĢ Go to ZyWALL/USG MONITOR > VPN Monitor > IPSec and verify the tunnel Up Time and the Inbound(Bytes)/Outbound(Bytes) traffic. Click OK.Ĥ Go back to Configuration and click Advanced …. In the Machine Authentication section, enter Shared Secret to be the pre-shared key of the IPSec VPN gateway the ZyWALL/USG uses for L2TP VPN over IPSec (zyx12345 in this example).

#ZYXEL VPN CLIENT MAC OS X PASSWORD#

Then, click Authentication Settings.ģ In the User Authentication section, enter Password which should be the same as Allowed User created in ZyWALL/USG (zyx123 in this example). Enter Account Name which should be the same as Allowed User created in ZyWALL/USG (L2TP_Remote_Users in this example).

Click Create.Ģ Configure Server Address to be the ZyWALL/USG’s WAN IP address (172.124.163.150 in this example). Set the Interface to be VPN, select VPN Type to be L2TP over IPSec.Ĭonfigure Service Name for you to identify the VPN configuration. Step 2: Set Up the L2TP VPN Tunnel on the Apple MAC OS X 10.11 El Capitan Operating Systemġ To configure L2TP VPN in OS X 10.11 operation system, go to System Preferences… > Network, click the ' +' button at the bottom left of the connections to add a new connection and configure as follows. Set the Next-Hop Type to Trunk and select the appropriate WAN trunk.ĬONFIGURATION > Network > Routing > Policy Route Set the Source Address to be the L2TP address pool. Set Incoming to Tunnel and select your L2TP VPN connection. Then, set Allowed User to the newly created object (L2TP_Remote_Users/zyx168 in this example).ĬONFIGURATION > VPN > L2TP VPN > Create new Object > UserĦ If some of the traffic from the L2TP clients needs to go to the Internet, create a policy route to send traffic from the L2TP tunnels out through a WAN trunk. Quick Setup > VPN Setup Wizard > Welcome > VPN Settings > Summary > Wizard Completedĥ Go to CONFIGURATION > VPN > L2TP VPN > Create new Object > User to add User Name and Password (4-24 characters). Quick Setup > VPN Setup Wizard > Welcome > VPN Settings > Summary

Click OK.Ĥ Continue to the next page to review your Summary and click Save. Quick Setup > VPN Setup Wizard > Welcome > VPN Settingsģ Configure the L2TP users’ IP address range from 192.168.30.10 to 192.168.30.20 for use in the L2TP VPN tunnel and check Allow L2TP traffic Through WAN. Type a secure Pre-Shared Key (8-32 characters). Click Next.Ģ Then, configure the Rule Name and set My Address to be the wan1 interface which is connected to the Internet. Step 1: Set Up the L2TP VPN Tunnel on the ZyWALL/USGġ In the ZyWALL/USG, go to CONFIGURATION > Quick Setup > VPN Setup Wizard, use the VPN Settings for L2TP VPN Settings wizard to create a L2TP VPN rule that can be used with the MAC OS X clients.

Zyxel vpn client mac os x